OTV Sensing — Magnetic Encoder Solutions

Off-Axis & Hollow-Shaft Magnetic Encoders

Precision rotary position sensing for space-constrained applications ±0.1° accuracy · 6–65 mm hollow bore · Non-contact · Dust & oil immune

Choose a hollow-shaft encoder system or a magnetic target

OME series

Start with the OME model table for bore, outside diameter, resolution, accuracy and controller interface. Review each model before choosing its mounting arrangement.

OMEC series

OTV-OMEC hollow-shaft absolute rotary encoders provide a thin-profile option with IP67-rated configurations. Check the selected assembly, connector and installation conditions.

Magnetic target only

Magnetic encoder rings and discs are intended for designs with their own readhead electronics. Select the IC, track geometry and mechanical carrier together.

Before release, verify runout, operating gap, signal quality, calibration and position repeatability after power cycling. Follow the hollow-shaft encoder assembly and calibration guide.

What Is an Off-Axis Magnetic Encoder?

An off-axis magnetic encoder is a rotary position sensor where the sensing element (Hall or MR chip) is positioned beside the rotating shaft rather than at its end. A diametrically magnetized ring or multi-pole magnet ring is mounted on the shaft, and the sensor reads the rotating magnetic field from the side — hence “off-axis.”

A hollow-shaft magnetic encoder takes this a step further: the magnet ring has a large center bore, allowing cables, shafts, or fluid lines to pass through the encoder. This enables true zero-backlash, bearingless integration into robot joints, servo motors, and medical equipment.

Off-Axis vs On-Axis: Key Difference

On-Axis

Sensor sits at the end of the shaft. Requires the shaft end to be accessible. Occupies axial space.

On-Axis Encoder Diagram

Off-Axis (Hollow-Shaft)

Sensor reads the magnet ring from the side. Shaft passes through the ring. Saves axial space.

On-Axis Encoder Diagram

How Magnetic Encoders Work

1

Magnet Ring Creates a Rotating Field

A multi-pole or diametrically magnetized ring is mounted on the rotating shaft. As the shaft turns, the magnetic field pattern rotates in sync. Key parameters: pole pair count, magnetic flux density, pole width uniformity.

2

Sensor Chip Detects Field Orientation

A magnetic encoder IC (Hall-effect or MR-based) placed adjacent to the ring measures the in-plane magnetic field components. The IC computes the instantaneous field angle using internal arctangent calculation.

3

Digital Output to Controller

The IC outputs absolute or incremental angle data via standard protocols — SSi, BiSS-C, SPI, ABZ, or UART — directly to the motor drive, robot controller, or PLC.

The advantages of off-axis magnetic sensing over optical encoders are decisive for industrial applications: no glass disc to crack, no LED to dim, no optical path to contaminate. The non-contact magnetic principle is inherently immune to dust, oil, condensation, and vibration.

Mainstream Magnetic Encoder Chips

The off-axis magnetic encoder ecosystem is built around dedicated encoder ICs. Each chip family has specific requirements for the magnet ring — pole count, field strength, geometry — that directly affect achievable resolution and accuracy.

ManufacturerKey IC SeriesTypeResolutionInterfaceOTV Ring Compatible
iC-HausiC-MU200, iC-MU150, iC-PVLHall Array18-22 bitBiSS-C, SSi, SPI, ABZ✓ Yes
RLS (Renishaw)Orbis, AksIM, LinACEHall Array14-20 bitBiSS-C, SSi, SPI✓ Yes
AMS (Osram)AS504x, AS5147, AS5600Hall Array12-14 bitSPI, I2C, ABZ, PWM✓ Yes

Additional encoder ICs from Melexis, Infineon, AKM, and others are also supported. View the full encoder IC compatibility guide →

Each IC has a defined magnetic input specification: the field strength range at the sensor location, typically 20–80 mT. The magnet ring must deliver the correct field amplitude at the air gap distance between ring surface and sensor. OTV designs magnet rings to match each chip’s optimal operating window. See: Magnetic Target for iC-Haus IC-MU200.

OTV Standard Off-Axis Magnetic Encoder — OME Series

The OME Series is OTV’s standard off-axis magnetic encoder product line. Each model features a hollow-shaft, bearingless design with a separated stator-rotor structure, with major encoder ICs listed above.

OTV OME Series Off-Axis Magnetic Encoder

OTV OME Series — Off-Axis Hollow-Shaft Magnetic Encoder

1. Basic Performance
ParameterOME06OME08OME10OME15OME20OME25OME35OME45OME65
ProductOTV-OME08 hollow-shaft magnetic encoderOTV-OME08 hollow-shaft magnetic encoderOTV-OME10 hollow-shaft magnetic encoderOTV-OME15 hollow-shaft magnetic encoderOTV-OME20 hollow-shaft magnetic encoderOTV-OME25 hollow-shaft magnetic encoderOTV-OME35 hollow-shaft magnetic encoderOTV-OME45 hollow-shaft magnetic encoderOTV-OME65 hollow-shaft magnetic encoder
Resolution17 bit18 bit17-18 bit17-18 bit17-19 bit17-19 bit17-20 bit17-20 bit17-20 bit
Max Static Error±0.1°±0.1°±0.1°±0.1°±0.1°±0.1°±0.1°±0.1°±0.1°
Repeatability±1 LSB±1 LSB±1 LSB±1 LSB±1 LSB±1 LSB±1 LSB±1 LSB±1 LSB
Max Speed6,000 rpm6,000 rpm6,000 rpm6,000 rpm6,000 rpm6,000 rpm5,000 rpm5,000 rpm5,000 rpm
RangeSingle Turn Absolute / Muti Turn Absolute Optional
DirectionCW Incrementing (Configurable)

2. Mechanical Dimensions & Mounting
ParameterOME06OME08OME10OME15OME20OME25OME35OME45OME65
Target Ring
OD/ID/T (mm)
22/6/222/10/229/10/229/15/239/20/249/25/255/35/2.564/45/2.584/65/2.5
Readhead
OD/ID/T (mm)
Angle (°)
28.5/8.5/4.15 36032/8/6.1 36038/14/3.85 36038/18/3.85 36054/21.2/5.8 19659/26/6.42 13867/42/6.1 15075/51/6.1 9096/70/6.1 77
Weight (approx.)8 g9g11 g13g15 g18 g22 g25 g30 g
Eccentricity±0.1 mm
Air Gap
(
Chip surface
to Target Ring)
0.5±0.1mm0.5±0.1mm0.5±0.1mm0.5±0.1mm1.3±0.1mm0.5±0.1mm0.5±0.1mm0.5±0.1mm0.5±0.1mm
Inertia
(kg·mm²)
0.290.320.690.782.585.4510.6318.8846.48

3. Environmental Conditions
Operating Temperature-30°C to +85°C
EMC StandardsIEC 61000-6-2, IEC 61000-6-4
Relative Humidity0-99% (non-condensing)
Shock Resistance100 g / 11 ms
Vibration0.04 g²/Hz (10 Hz – 2,000 Hz)

4. Electrical & Interface
Supply Voltage5 V ±5%
Current≤100 mA
Electrical Connector8-Pin Connector
Output ProtocolsSSi, BiSS-C,SPI, ABZ

Download Product Datasheets

PDF datasheet with full mechanical drawings, electrical specs, and ordering codes

All models: Single-turn/Muti-turn absolute · Non-contact · Separated stator-rotor · FR-4 material · Additional sizes and custom configurations available on request. The product includes mounting bolts, a 10 cm wire harness with connector.

OTV Sensing · Hollow-Shaft Absolute Encoder

OTV-OMEC Series – Thin-Profile IP67 Encoders

For rotary stages, robot joints, and compact actuators that need an open center bore, the OTV-OMEC is a non-contact, off-axis absolute rotary encoder with a slim ring assembly. Single-turn position is available at power-up, with bore sizes from 25 mm to 65 mm.

The ring uses an axial magnetization pattern. Resolution, speed, mounting pattern, and thickness vary by configuration; the IP67 rating applies to the specified encoder system and should be confirmed for the final installation.

OTV-OMEC hollow-shaft absolute rotary encoder
Absolute feedback16-20 bit · single-turn
Thin profiletotal 7 mm thickness
System protectionIP67 configuration
Position accuracy±0.1° (system spec)

OTV-OMEC model selection by bore

Compare the bore first, then check ring outside diameter, mounting holes, and axial space. The two ID25 mounting options are listed separately because their hole patterns and thickness differ.

OTV modelBore / IDRing ODResolutionMax. speed*Mounting holesThickness
OTV-OMEC-ID25 · 4-hole25 mm49 mm16-20 bitUp to 9,500 rpm42.0 mm
OTV-OMEC-ID25 · 6-hole25 mm49 mm16-20 bitUp to 9,500 rpm63.9 mm
OTV-OMEC-ID31.531.5 mm49 mm16-20 bitUp to 9,500 rpm02.0 mm
OTV-OMEC-ID6262 mm84 mm16-20 bitUp to 4,700 rpm01.8 mm
OTV-OMEC-ID6565 mm84 mm16-20 bitUp to 4,700 rpm82.5 mm

* Maximum speed depends on ring size and operating conditions. Confirm the rating for the final assembly.

Electrical and environmental data

5 V +/- 5% supply; <85 mA no-load current at 25 °C; <100 ms startup; -30 °C to +85 °C; +/-0.5 mT external magnetic field during operation.

Interfaces and connection

BiSS-C, SSI, SPI, or Tamagawa, depending on configuration. Connector options include DB9, DB15, 8-pin M12, or bare wire. Confirm protocol, pinout, and cable requirements for the controller.

System accuracy and IP protection depend on the selected configuration and installation. Check alignment, air gap, ring runout, sealing, and controller interface before design release.

View full OTV-OMEC specifications and options ?

Where Off-Axis Magnetic Encoders Excel

🤖

Robot Joints

Hollow shaft for cable pass-through. Integrated into cobot joints.

⚙

Servo Motors

Off-axis feedback without extending motor length. Motor commutation sensing.

🏥

Medical Devices

CT gantry rotation, surgical robots, prosthetic joints. Sterile-compatible, non-contact.

📦

AGV & Mobile Robots

Steering angle feedback immune to drive motor magnetic interference.

✈

Aerospace Actuators

Flight control surfaces, landing gear. Wide temperature, vibration resistant.

🌎

Oil & Gas Equipment

Downhole tool positioning. High-temperature magnets up to 250°C.

Why OTV for Off-Axis Magnetic Encoder Solutions

① Magnet Ring & Encoder from ONE Supplier

We manufacture both the precision magnet ring and the encoder module. No finger-pointing between magnet supplier and sensor integrator — one partner, one guarantee.

② In-House Precision Magnetization

Custom-built magnetization fixtures, closed-loop current control, 100% pole-width inspection. Custom rings shipped in 2 weeks.

③ Full Encoder IC Compatibility

Magnet rings characterized for iC-Haus, RLS, AMS encoder ICs. Field strength, air gap, and pole geometry matched to each chip’s optimal operating point.

④ Direct Replacement for RLS & Competitors

Form-fit-function compatible magnet rings for RLS magnetic encoders. Customization possible at no NRE for qualified projects.

Need an Off-Axis Magnetic Encoder Solution?

Tell us your encoder IC, pole count, ID/OD, and accuracy target. We’ll recommend the optimal OME series encoder or magnet ring — or design one from scratch.

Standard samples in 1 week. Custom rings in 2–4 weeks. Engineering support included.

Contact OTV Engineering Team →

thomas@otvsensing.com

OTV Precision Sensing | www.otvsensing.com | Suzhou, China

Shopping Cart